Enables interaction between different logic levels in the same system e.g. send 5V logic signals to 3.3V tolerant inputs. Signals can pass in both...
£0.59... more info
Prototyping double-sided pad board fits the Wemos D1-Mini wi-fi board headers.
DC buck converter module based on the MP2307 IC. Input 4.75V - 23Vdc. Output 1V-17Vdc Output variable by on board miniature preset potentiometer. Our...
Input 0.9V - 5Vdc. Output 5Vdc @ 650mA max. via USB type A socket. Ideally suited to charger projects.
Stereo power amplifier based on the PAM8403 class-D chip. 2.5-5V dc supply and highly efficient class of operation make this ideally suited to...
Digital (active low) and analogue outputs. Supply voltage 3v3 - 5Vdc. Sensitivity adjustment. Sensitive in the 760nm - 1100nm band. An example of...
£0.88... more info
Stereo power amplifier based on the PAM8403 class-D chip. Module incorporates volume control with on/off switch at fully anti-clockwise rotation....
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
Charger module for 3.7V lithium power (LiPo) packs which do not include their own protection circuit. Feeds a 1A charge current to the battery and...
£1.00... more info
Input 2V - 24Vdc. via solder pads or micro-USB socket. Output 28V max. Rated output current 2A max, 1A max continuous recommended, 3.5W approx. Buck...
Electret microphone with comparator circuit for sound detection. Power ON and sound detected LED indicators. Digital and analogue outputs....
A module for detecting moisture levels in soil. Ideal for experimenting with automatic watering systems and alarms. Consisting of a resistive...
£1.08... more info
Input 3V - 40Vdc. Output 1.3V-35Vdc Rated output current 2A max continuous, 3A with additional heatsinking. Buck converter operating at 150kHz - max...
2-channel H-bridge motor driver board able to drive two independent motors at up to 800mA each. Can also drive a single four line two phase stepper...
STM8S003F3P6 breakout board. Processor - STM8S003F3P6 16MHz 8-bit. 8K Flash memory, 1K RAM & 128 bytes EEPROM. 10-bit ADC, 3 timers, UART, SPI, I2C....
Break out the Nano I/O to screw terminals. Nano pins push fit into central female headers. Board provided as a kit so soldering assembly is required....
£1.26... more info
NRF24L01+ 2.4GHz Transceiver Module Data transfer up to 2Mbps. 125 Channels, Multi-point communication and frequency hopping to meet the...
"Digital Tube" display module - 0.36" This module uses a two pin serial interface to accept display data to the onboard TM1637 IC. For Arduino use...
Remote control experimenters kit containing remote handset with coin cell battery, shielded IR sensor, connector board and 3-way f/f jumper lead set....
433MHz RF link modules for remote control applications. Widely used in Arduino based projects. Transmitter Specs: Voltage: 3.3V to 12V Range: 20m to...
Detect the distance to objects in front of the sensor using an ultrasonic ping. 5V operation suitable for use with microcontrollers, Arduino, etc. An...
£1.72... more info
Stereo power amplifier based on the PAM8610 class-D chip. 7-15V dc supply, input impedance 15k, 4 Ohm - 8 Ohm output impedance. 15W+15W into a 4 Ohm...
PCB Mounted 10A Change-over Relay. On-board transistor relay driver circuit and led indicator. Some versions may include power and active led...
A low cost, accurate I2C real-time clock. with an integrated 32K AT24C32 EEPROM. Supply voltage 3.3 V to 5.5 V A coin cell battery holder allows...
PIR motion sensor with high/low TTL 3.3V output signal. Sensitivity (up to 7m) and output duration (20s - 5min approx.) adjustable. 5V - 20V DC...
PIR motion sensor with operating in the 2.7V to 12Vdc supply range. Sensitivity 3-5m with output low to high for 2 secs on detection of motion....
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. USB A plug connects to PC with...
Triaxial accelerometer and gyroscope with 6 degrees of freedom. I2C serial interface. 5Vdc supply voltage - Arduino friendly. Applications available...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. Connects to PC via micro-USB...
Add Wi-fi and web capabilities to your project with this module which is currently in rapid development. The onboard firmware can and should be...