M050
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
£0.97
Add:
M069
PIR motion sensor with operating in the 2.7V to 12Vdc supply range. Sensitivity 3-5m with output low to high for 2 secs on detection of motion....
£1.97
Add:
M085
Motor driver shield for Arduino - compatible with the Adafruit motor driver library. The board includes two L293D motor drivers and one 74HC595 shift...
£3.37
Add:
MTR8
Motor voltage range 3-12Vdc (5V-9V recommended). 70-250mA Motor & gearbox dimensions 70 x 22 x 18mm approx. 70-140 rpm approx. Torque 1kgf.cm approx....
£2.38
Add:
M083
MP3 decoder module based on the GPD2856C chip. 3.7-5.5Vdc supply via on-board micro-USB port or BAT+/- solder pads. 4 push button control - short...
£2.52
Add:
M057
Clone of the Arduino Nano 3.0 with ATMega328P microcontroller. 100% compatible. This module does not have the header pins fitted (they are supplied...
£3.67
Add:
M025
Clone of the Arduino Nano 3.0 with ATMega328P microcontroller. 100% compatible and includes a free USB cable.
£5.52
Add:
M061
Break out the Nano I/O to screw terminals. Nano pins push fit into central female headers. Board provided as a kit so soldering assembly is required....
£1.26
Add:
M021
NRF24L01+ 2.4GHz Transceiver Module Data transfer up to 2Mbps. 125 Channels, Multi-point communication and frequency hopping to meet the...
£1.49
Add:
M067
Bluetooth Low Energy (BLE) module based on the Nordic nRF51822 microcontroller. See also the BLE400 (M068) development board for this module.
£6.62
Add:
M095
Stereo power amplifier based on the PAM8610 class-D chip. 7-15V dc supply, input impedance 15k, 4 Ohm - 8 Ohm output impedance. 15W+15W into a 4 Ohm...
£1.78
Add:
M078
Real time clock (RTC) module based on the PCF8563. 400kHz I2C bus communications. Provides year, month, day, weekday, hours, minutes, and seconds...
£1.69
Add:
M049
I2C comms interface - address 0x48 Supply voltage 2.5V - 6Vdc. Onboard light sensor, thermistor and potentiometer connected to three ADC channels via...
£2.35
Add:
M076
Clone of the Arduino Pro Mini fitted with an ATMega168 microcontroller operating at 3.3V 8MHz. 100% compatible. The Pro Mini was designed as a low...
£2.48
Add:
M071
Clone of the Arduino Pro Mini with ATMega328P microcontroller operating at 3.3V 8MHz. 100% compatible. The Pro Mini was designed as a low cost...
£3.11
Add:
M074
Clone of the Arduino Pro Mini with ATMega328P microcontroller operating at 5V 16MHz. 100% compatible. The Pro Mini was designed as a low cost...
£3.49
Add:
M013
PCB Mounted 10A Change-over Relay. On-board transistor relay driver circuit and led indicator. Inputs for 5Vdc supply and relay operating signal (5V...
£1.79
Add:
M017
Opto-isolated 10A Change-over Relay. On-board optocoupler circuit with power and relay active led indicators. Inputs for 5Vdc supply and relay...
£1.90
Add:
M064
Double relay module. Inputs Gnd, Vcc (5Vdc), channel 1 signal (active low), channel 2 signal (active low). Channel signals are optically isolated...
£2.42
Add:
M081
4-Channel relay module. Inputs Gnd, Vcc (5Vdc), channel select signal 1-4 (active low). Channel signals are optically isolated from the relay coils....
£3.11
Add:
M075
8-Channel relay module. Inputs Gnd, channels 1-8 signal (active low), Vcc (5Vdc). Channel signals are optically isolated from the relay coils. Option...
£5.10
Add:
M089
RF remote control switch. Consists of receiver module with 10A changeover relay and key-fob remote control with extendable antenna and sliding cover....
£6.00
Add:
M035
A module for detecting moisture levels in soil. Ideal for experimenting with automatic watering systems and alarms. Consisting of a resistive...
£0.88
Add:
M014
Electret microphone with comparator circuit for sound detection. Power ON and sound detected LED indicators. Digital and analogue outputs....
£1.07
Add:
M082
DC buck converter module based on the MP2307 IC. Input 4.75V - 23Vdc. Output 1V-17Vdc Output variable by on board miniature preset potentiometer. Our...
£0.65
Add:
M058
Input 4.75V - 40Vdc. Output 0.9V-30Vdc Power rating 6W. Output current 800mA max continuous, 1A short duration. High efficiency, high frequency buck...
£2.18
Add:
M060
Input 2V - 24Vdc. via solder pads or micro-USB socket. Output 28V max. Rated output current 2A max, 1A max continuous recommended, 3.5W approx. Buck...
£0.94
Add:
M063
A high power, variable output, DC-DC boost converter with integrated voltage display. The display can show either input or output voltage, selected...
£5.52
Add:
M044
Input 0.9V - 5Vdc. Output 5Vdc @ 650mA max. via USB type A socket. Ideally suited to charger projects.
£0.67
Add:
M077
Processor - Powerful ARM 32bit Cortex-M3 72MHz CPU 64K Flash memory & 20K SRAM. 33 I/O pins. and 3.3V operating voltage. Supplied with 0.1" pitch...
£3.41
Add:
