Enables interaction between different logic levels in the same system e.g. send 5V logic signals to 3.3V tolerant inputs. Signals can pass in both...
DC buck converter module based on the MP2307 IC. Input 4.75V - 23Vdc. Output 1V-17Vdc Output variable by on board miniature preset potentiometer. Our...
Input 0.9V - 5Vdc. Output 5Vdc @ 650mA max. via USB type A socket. Ideally suited to charger projects.
Stereo power amplifier based on the PAM8403 class-D chip. 2.5-5V dc supply and highly efficient class of operation make this ideally suited to...
Digital (active low) and analogue outputs. Supply voltage 3v3 - 5Vdc. Sensitivity adjustment. Sensitive in the 760nm - 1100nm band. An example of...
A module for detecting moisture levels in soil. Ideal for experimenting with automatic watering systems and alarms. Consisting of a resistive...
Input 2V - 24Vdc. via solder pads or micro-USB socket. Output 28V max. Rated output current 2A max, 1A max continuous recommended, 3.5W approx. Buck...
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
Charger module for 3.7V lithium power (LiPo) packs which do not include their own protection circuit. Feeds a 1A charge current to the battery and...
Electret microphone with comparator circuit for sound detection. Power ON and sound detected LED indicators. Digital and analogue outputs....
Input 3V - 40Vdc. Output 1.3V-35Vdc Rated output current 2A max continuous, 3A with additional heatsinking. Buck converter operating at 150kHz - max...
Break out the Nano I/O to screw terminals. Nano pins push fit into central female headers. Board provided as a kit so soldering assembly is required....
STM8S003F3P6 breakout board. Processor - STM8S003F3P6 16MHz 8-bit. 8K Flash memory, 1K RAM & 128 bytes EEPROM. 10-bit ADC, 3 timers, UART, SPI, I2C....
NRF24L01+ 2.4GHz Transceiver Module Data transfer up to 2Mbps. 125 Channels, Multi-point communication and frequency hopping to meet the...
Prototyping shield supplied with mini-breadboard. Two general purpose LEDs, push switch and reset button on board. Suitable for circuit prototyping...
433MHz RF link modules for remote control applications. Widely used in Arduino based projects. Arduino tutorial available here . Transmitter Specs:...
Remote control experimenters kit containing remote handset with coin cell battery, shielded IR sensor, connector board and 3-way f/f jumper lead set....
Real time clock (RTC) module based on the PCF8563. 400kHz I2C bus communications. Provides year, month, day, weekday, hours, minutes, and seconds...
PIR motion sensor with high/low TTL 3.3V output signal. Sensitivity (up to 7m) and output duration (20s - 5min approx.) adjustable. 5V - 20V DC...
"Digital Tube" display module - 0.36" This module uses a two pin serial interface to accept display data to the onboard TM1637 IC. For Arduino use...
PCB Mounted 10A Change-over Relay. On-board transistor relay driver circuit and led indicator. Inputs for 5Vdc supply and relay operating signal (5V...
A low cost, accurate I2C real-time clock. with an integrated 32K AT24C32 EEPROM. Supply voltage 3.3 V to 5.5 V A coin cell battery holder allows...
Opto-isolated 10A Change-over Relay. On-board optocoupler circuit with power and relay active led indicators. Inputs for 5Vdc supply and relay...
Detect the distance to objects in front of the sensor using an ultrasonic ping. 5V operation suitable for use with microcontrollers, Arduino, etc. An...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. USB A plug connects to PC with...
PIR motion sensor with operating in the 2.7V to 12Vdc supply range. Sensitivity 3-5m with output low to high for 2 secs on detection of motion....
I2C comms interface - address 0x48 Supply voltage 2.5V - 6Vdc. Onboard light sensor, thermistor and potentiometer connected to three ADC channels via...
Triaxial accelerometer and gyroscope with 6 degrees of freedom. I2C serial interface. 5Vdc supply voltage - Arduino friendly. Applications available...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. Connects to PC via micro-USB...
Input 4.75V - 40Vdc. Output 0.9V-30Vdc Power rating 6W. Output current 800mA max continuous, 1A short duration. High efficiency, high frequency buck...