Triaxial accelerometer and gyroscope with 6 degrees of freedom. I2C serial interface. 5Vdc supply voltage - Arduino friendly. Applications available...
Stereo power amplifier based on the PAM8403 class-D chip. 2.5-5V dc supply and highly efficient class of operation make this ideally suited to...
Enables interaction between different logic levels in the same system e.g. send 5V logic signals to 3.3V tolerant inputs. Signals can pass in both...
"Digital Tube" display module - 0.36" This module uses a two pin serial interface to accept display data to the onboard TM1637 IC. For Arduino use...
Input 4V - 32Vdc. Output 1.3V-30Vdc Constant max. output current can be varied up to 5A. Set the output voltage off load, then set the current limit...
A programmable waveform generator module. Frequency range: 0-12.5MHz Waveforms: Sine, Square, Triangle. Frequency and phase easily programmed and...
This clone of the Arduino Uno R3 uses a surface mount ATMega328P together with CH340G uart to handle the USB comms. 100% compatible and includes a...
A motherboard designed to aid the development of applications for the Nordic nRF51822 microcontroller. Socket accepts the Bluetooth4.0 module (M067)....
433MHz RF link modules for remote control applications. Widely used in Arduino based projects. Arduino tutorial available here . Transmitter Specs:...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. USB A plug connects to PC with...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. Connects to PC via micro-USB...
A low cost, accurate I2C real-time clock. with an integrated 32K AT24C32 EEPROM. Supply voltage 3.3 V to 5.5 V A coin cell battery holder allows...
Ethernet network adaptor module based on the ENC28J60 chip. SPI interface. 3.3V supply. Arduino compatible using a variety of available libraries...
Wi-fi and Bluetooth capable development board using the ESP-WROOM-32 chip. 32-bit dual core processor. Up to 240MHz with 512kB RAM. Peripherals...
Based around the ESP8266 ESP-12 and NodeMCU firmware this module provides an integrated Arduino-like hardware platform for developing wifi IoT...
Add Wi-fi and web capabilities to your project with this module which is currently in rapid development. The onboard firmware can and should be...
Connect your Arduino to the network or Internet. Includes a micro SD card slot. Note that the R3 Uno has a couple of extra ways on the female sockets...
Bluetooth communications module mounted on base board for easy plug-in connection and voltage regulation. Ideal for use in Arduino serial...
Bluetooth communications module mounted on base board for easy plug-in connection. Ideal for use in Arduino serial communication projects. Module...
Detect the distance to objects in front of the sensor using an ultrasonic ping. 5V operation suitable for use with microcontrollers, Arduino, etc. An...
PIR motion sensor with high/low TTL 3.3V output signal. Sensitivity (up to 7m) and output duration (20s - 5min approx.) adjustable. 5V - 20V DC...
BLE communication module based on the CC2541 IC. Power supply - 3.6V-6Vdc Logic level - 3.3V. For communication with Arduino boards use a simple...
Digital (active low) and analogue outputs. Supply voltage 3v3 - 5Vdc. Sensitivity adjustment. Sensitive in the 760nm - 1100nm band. An example of...
Remote control experimenters kit containing remote handset with coin cell battery, shielded IR sensor, connector board and 3-way f/f jumper lead set....
Input 3V - 40Vdc. Output 1.3V-35Vdc Rated output current 2A max continuous, 3A with additional heatsinking. Buck converter operating at 150kHz - max...
Clone of the Arduino Mega 2560. 100% compatible and includes a USB cable.
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
PIR motion sensor with operating in the 2.7V to 12Vdc supply range. Sensitivity 3-5m with output low to high for 2 secs on detection of motion....
Motor driver shield for Arduino - compatible with the Adafruit motor driver library. The board includes two L293D motor drivers and one 74HC595 shift...
Motor voltage range 3-12Vdc (5V-9V recommended). 70-250mA Motor & gearbox dimensions 70 x 22 x 18mm approx. 70-140 rpm approx. Torque 1kgf.cm approx....