In-circuit programmer for AVR microcontrollers. Linux, Mac OSX and Windows compatible. Supplied with 10-way IDC lead.
Clone of the Arduino Uno R3. DIL socket mounted processor 100% compatible and includes a USB cable.
433MHz RF link modules for remote control applications. Widely used in Arduino based projects. Arduino tutorial available here . Transmitter Specs:...
Connect your Arduino to the network or Internet. Includes a micro SD card slot. Note that the R3 Uno has a couple of extra ways on the female sockets...
PCB Mounted 10A Change-over Relay. On-board transistor relay driver circuit and led indicator. Inputs for 5Vdc supply and relay operating signal (5V...
Electret microphone with comparator circuit for sound detection. Power ON and sound detected LED indicators. Digital and analogue outputs....
Opto-isolated 10A Change-over Relay. On-board optocoupler circuit with power and relay active led indicators. Inputs for 5Vdc supply and relay...
USB-to-Serial converter based on the CP2102 chip. For debugging, firmware updating and general serial communications. USB A plug connects to PC with...
NRF24L01+ 2.4GHz Transceiver Module Data transfer up to 2Mbps. 125 Channels, Multi-point communication and frequency hopping to meet the...
In-circuit programmer for AVR microcontrollers. Supplied with 6-way IDC lead for connection to the target. USB powered. Jumper in place sends 5V to...
Clone of the Arduino Nano 3.0 with ATMega328P microcontroller. 100% compatible and includes a free USB cable. Note: Header pins are supplied but may...
Bluetooth communications module mounted on base board for easy plug-in connection and voltage regulation. Ideal for use in Arduino serial...
Bluetooth communications module mounted on base board for easy plug-in connection. Ideal for use in Arduino serial communication projects. Module...
Add Wi-fi and web capabilities to your project with this module which is currently in rapid development. The onboard firmware can and should be...
A low cost, accurate I2C real-time clock. with an integrated 32K AT24C32 EEPROM. Supply voltage 3.3 V to 5.5 V A coin cell battery holder allows...
PIR motion sensor with high/low TTL 3.3V output signal. Sensitivity (up to 7m) and output duration (20s - 5min approx.) adjustable. 5V - 20V DC...
A module for detecting moisture levels in soil. Ideal for experimenting with automatic watering systems and alarms. Consisting of a resistive...
Based around the ESP8266 ESP-12 and NodeMCU firmware this module provides an integrated Arduino-like hardware platform for developing wifi IoT...
Clone of the Arduino Mega 2560. 100% compatible and includes a USB cable.
BLE communication module based on the CC2541 IC. Power supply - 3.6V-6Vdc Logic level - 3.3V. For communication with Arduino boards use a simple...
Enables interaction between different logic levels in the same system e.g. send 5V logic signals to 3.3V tolerant inputs. Signals can pass in both...
Input 0.9V - 5Vdc. Output 5Vdc @ 650mA max. via USB type A socket. Ideally suited to charger projects.
Digital (active low) and analogue outputs. Supply voltage 3v3 - 5Vdc. Sensitivity adjustment. Sensitive in the 760nm - 1100nm band. An example of...
Clone of the Arduino Pro Mini fitted with an ATMega168 microcontroller operating at 5V 16MHz. 100% compatible. The Pro Mini was designed as a low...
Remote control experimenters kit containing remote handset with coin cell battery, shielded IR sensor, connector board and 3-way f/f jumper lead set....
This clone of the Arduino Uno R3 uses a surface mount ATMega328P together with CH340G uart to handle the USB comms. 100% compatible and includes a...
I2C comms interface - address 0x48 Supply voltage 2.5V - 6Vdc. Onboard light sensor, thermistor and potentiometer connected to three ADC channels via...
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
Prototyping shield supplied with mini-breadboard. Two general purpose LEDs, push switch and reset button on board. Suitable for circuit prototyping...
"Digital Tube" display module - 0.36" This module uses a two pin serial interface to accept display data to the onboard TM1637 IC. For Arduino use...